The Autonerdz Community Forums - Hello From Shakey City

crackerclicker Super Nerd Picogroup Offline Elevation 834 ft Posts: 2,358 Watertown Wisconsin USA Gender:	Re: Hello From Shakey City Reply #15 - Jun 9^th, 2014 at 12:45pm Olly wrote on Jun 9^th, 2014 at 12:20am: I would just go with the pico alone if they hadn't started fitting wideband O2 sensors to all the current stuff, which looks like it makes a scantool is a nessesity now. Something to consider. http://www.autonerdz.com/ampprobes.html Welcome aboard the crazy train, Olly.
Back to top	IP Logged

Olly

Senior Member
Picogroup

Offline

Ollymoto

Posts: 113

Christchurch
New Zealand
Gender: male

Re: Hello From Shakey City
Reply #16 - Jun 10^th, 2014 at 2:29am

crackerclicker wrote on Jun 9^th, 2014 at 12:45pm:

Something to consider. http://www.autonerdz.com/ampprobes.html

Yea i found this but was not sure which clamp would be the right one for doing Wideband sensors. I already have one like the 20/60a one on there. I thought there was a specific one just for micro amps?

I had considered making a fly lead with a length of wire on the signal wires loooped 10x over to amplify signal to use the clamp i already have but time is always against me.

Back to top

www.OllyMoto.co.nz
Motorcycle Servicing, Repairs & Diagnostics

WWW

IP Logged

Tom Roberts Autonerdz Administrator Picogroup Offline Autonerdz Founder Posts: 8,595 Olympia Washington USA Gender:	Re: Hello From Shakey City Reply #17 - Jun 10^th, 2014 at 8:22am The K110 Microprobe is the only one we know of capable of doing micro amps. We no longer carry this probe due to market pressures and it was no longer a profitable item. http://www.aemc.com/products/pdf/2111.73.pdf http://www.autonerdz.com/cgi/yabb2/YaBB.pl?num=1274201795/0
Back to top	Tom Roberts Forums Administrator IP Logged

busjockey

LSD Guide

Offline

The Diesel Nerd

Posts: 3,442

Champaign
Illinois
USA
Gender: male

Re: Hello From Shakey City
Reply #18 - Jun 10^th, 2014 at 9:34am

Tom, do you know of anyone using this low current probe to look at a Nox sensor signal? I have been contemplating on buying one to use it for this and other low currents. Think this would also work great to verify current to multiplex modules. Years ago I had a Allen Bradley input card go bad by intermittently shorting to ground. It made my meter show the supply voltage drop from 13.6 volts to under the 8.0 volt threshold for the module to recognize the signal. I figured it out by isolating and testing the wire first, but it would have been cool to see the current spike upward on it.

Back to top

Busjockey

IP Logged

Tom Roberts

Autonerdz Administrator
Picogroup

Offline

Autonerdz Founder

Posts: 8,595

Olympia
Washington
USA
Gender: male

Re: Hello From Shakey City
Reply #19 - Jun 10^th, 2014 at 10:10am

busjockey wrote on Jun 10^th, 2014 at 9:34am:

do you know of anyone using this low current probe to look at a Nox sensor signal?

No. The probe is very accurate, but does not have a very fast response time. Great for things that don't need that fast a response though. Wideband and AF sensors, MAF current, magneto resistive WSS, etc...

Back to top

Tom Roberts
Forums Administrator

IP Logged

Nikk

Guru Member
Picogroup

Offline

Posts: 256

Christchurch
New Zealand
Gender: male

Re: Hello From Shakey City
Reply #20 - Jun 10^th, 2014 at 4:13pm

Hi Olly,
Welcome to the sqiggely line club, nice to see someone local.
I can not speak highly enough of the people here, always ready to help.
Autonerdz is the only place to consider buying a pico.

Olly wrote on Jun 10^th, 2014 at 2:29am:

I had considered making a fly lead with a length of wire on the signal wires loooped 10x over to amplify signal to use the clamp i already have but time is always against me.

You could then create your own known good database under differing conditions from a near new machine.
Make sure you save any harness & plugs off old sensors.

Back to top

IP Logged

busjockey LSD Guide Offline The Diesel Nerd Posts: 3,442 Champaign Illinois USA Gender:	Re: Hello From Shakey City Reply #21 - Jun 10^th, 2014 at 7:49pm I think the low current probe will work on Nox sensors, check out this video by ADPT Training, very cool. http://youtu.be/VsR_P-14K0U
Back to top	Busjockey IP Logged

busjockey LSD Guide Offline The Diesel Nerd Posts: 3,442 Champaign Illinois USA Gender:	Re: Hello From Shakey City Reply #22 - Jun 10^th, 2014 at 7:50pm Think I might be investing in that micro amp probe.
Back to top	Busjockey IP Logged

Olly

Senior Member
Picogroup

Offline

Ollymoto

Posts: 113

Christchurch
New Zealand
Gender: male

Re: Hello From Shakey City
Reply #23 - Jun 11^th, 2014 at 12:28am

Olly wrote on Jun 9^th, 2014 at 12:20am:

would just go with the pico alone if they hadn't started fitting wideband O2 sensors to all the current stuff, which looks like it makes a scan tool is a necessity now. Roll Eyes

Right seems due to my ignorance/ incompetence that not all sensors are wide band as i originally thought. Being such a noob i think i couldn't get a signal out of the ones i was testing before as my scope has a slow buffer rate when set to 1.0sec time scale and takes a while to display the waveform (very laggy). Being impatient i didnt give it chance to display hence no recognizable waveform. Soooo

I will go back and check the ones i had thought were Wideband and see if i can get readings, If so it means that the new pico may get bumped to the top of the wish list over the scan tool! Grin

Back to top

www.OllyMoto.co.nz
Motorcycle Servicing, Repairs & Diagnostics

WWW

IP Logged

busjockey

LSD Guide

Offline

The Diesel Nerd

Posts: 3,442

Champaign
Illinois
USA
Gender: male

Re: Hello From Shakey City
Reply #24 - Jun 11^th, 2014 at 6:45am

I had the same thoughts too Olly, but after thinking about it myself, the Pico from Tom was the way to go. We pretty much have all the factory scan tools where I work so I decided the pico first.

I want to get a Scan tool next but since I discovered the nox sensor video from adpt training, I have started to druel over that micro probe and what I could do with it. I'm hoping to use it to see nox output from the engine and compare it to what is coming out of the scr side nox sensor so I can gauge the health of the dpf system. One more month till I have funds, so If I get one I will show everyone how it looks.

Back to top

Busjockey

IP Logged

Olly Senior Member Picogroup Offline Ollymoto Posts: 113 Christchurch New Zealand Gender:	Re: Hello From Shakey City Reply #25 - Jun 12^th, 2014 at 2:19am Yea After a coupe of tests today on bikes that i thought had Wideband sensors turned out to be regular O2 the descision is to go with a pico kit from Tom next. Just gotta get saving a bit but hopefully within the next 6 months.
Back to top	www.OllyMoto.co.nz Motorcycle Servicing, Repairs & Diagnostics WWW IP Logged

Olly Senior Member Picogroup Offline Ollymoto Posts: 113 Christchurch New Zealand Gender:	Re: Hello From Shakey City Reply #26 - Jun 12^th, 2014 at 2:21am Nikk wrote on Jun 10^th, 2014 at 4:13pm: Welcome to the sqiggely line club, nice to see someone local. Hi Nikk yea good to find local people with a similar mindset. Where abouts in CHCH are you based?
Back to top	www.OllyMoto.co.nz Motorcycle Servicing, Repairs & Diagnostics WWW IP Logged

autosparky Super Nerd Picogroup Offline blind worker Posts: 2,398 Porirua New Zealand Gender:	Re: Hello From Shakey City Reply #27 - Jul 18^th, 2014 at 7:06pm Welcome to nerdz I'm in Wellington running a mobile auto electrical services just for the trade. Was down your way in Easter for a south Island holiday. Sorry not a motorcycle tech but you might find car stuff very similar these days and the scoping technique will always be the same
Back to top	can't see, can't hear, can't remember IP Logged

Olly

Senior Member
Picogroup

Offline

Ollymoto

Posts: 113

Christchurch
New Zealand
Gender: male

Re: Hello From Shakey City
Reply #28 - Jul 21^st, 2014 at 12:19am

Hi Autosparky,

Ye aim hoping to learn lots from browsing the threads and seeing what goes on in the car world as many of the systems share similar traits or at least test methods and waveform analysis techniques.

I pop up your way every now and again to visit my family in the capital, quite nice up there, nearly moved up after the quakes but descided to stay put due to Mrs's family being dowm here.

Back to top

www.OllyMoto.co.nz
Motorcycle Servicing, Repairs & Diagnostics

WWW

IP Logged

	Welcome, Guest. Please Login or Register