NEW!!
Set of 4 Colored Premium Test Leads: BNC Plug to 4 mm
The ground lead is detachable on all except the Blue channel A lead.
Available in standard 3 meter and extended 5 meter lengths.
Set of Four - 3 Meter $165.00 + $25.00 S&H UPS 3 Day
Set of four - 5 Meter $190.00 + $25.00 S&H UPS 3 Day
Individual 3 meter leads
Blue $49.50
Red $49.50
Green $49.50
Yellow $49.50
_________________________________________________________________________________________________
USB Cables
These new cables are manufactured to Pico's specifications to help PicoScope users with poor quality or sloppy PC USB ports. These cables will likely help those who are experiencing occasional scope to PC communication disruptions.
Available in 1.8m (approx. 6 ft) and 4.5m (approx. 14.5 ft)
1.8m $8.25
4.5m $16.50
_________________________________________________________________________________________________
Coil On Plug Extension leads
Coil-on-Plug extension leads are the simple accessory that allow you to take accurate secondary ignition measurements on Coil-on-Plug ignition systems.
Coil-on-Plug extension leads are designed to aid diagnostics on secondary ignition circuits by allowing an HT measurement to be made when there are no, or limited access, to any spark plug leads.
Also available is a set of 4 COP extension leads that is ideal for use with cartridge coil-packs.
Single $41.23
Set of Four $156.73
____________________________________________________________________________________________________
S-Hook
This small but essential accessory makes it easy to keep all those test leads tidy in the engine bay.
The S-hook is about 100 mm (4 in) long and coated in plastic and rubber to protect the vehicle's paintwork and your cables. Hook one end underneath the bonnet or hood, and use the other end to hang a bundle of cables up to about 25 mm (1 in) thick.
$3.30 each
____________________________________________________________________________________________________
Additional Mixmaster Secondary Lead Set
A set of four short secondary leads for the Mixmaster Secondary Mixer.
$99.00 set of four
____________________________________________________________________________________________________
60 A AC/DC Current Clamp
This low amp probe is an improved version of the PP218 60 amp current clamp and features superior noise rejection.
The PP264 is terminated in a BNC connector and so can be connected directly to the PicoScope oscilloscope.
In use there is no need to break into the circuit or disturb the isolation as the opening jaws simply clamp around the current carrying conductor. No electrical contact is required.
$163.35 each
____________________________________________________________________________________________________
600 A AC/DC Current Clamp
This high amp probe is an improved version of the PP179 600 A current clamp and features superior noise rejection.
The PP266 is terminated in a BNC connector and so can be connected directly to a Pico automotive oscilloscope.
$163.35 each
____________________________________________________________________________________________________
2000 A AC/DC Current Clamp
The PP253 current clamp is suitable for measuring currents of up to 2000 amps DC or 1500 amps AC.
Note: the PP253 current clamp is supplied with shrouded 4 mm (banana) plug type connectors so can not be plugged directly into a PicoScope oscilloscope. We recommend the use of the TA000 or TA020 automotive test lead to connect the current clamp to the oscilloscope. Alternatively the MI078 BNC to 4 mm plug adaptor can be used.
$163.35 each
____________________________________________________________________________________________________
60 MHz Oscilloscope Probe (MI007)
This high-quality general purpose oscilloscope probe has a 60 MHz bandwidth. A two position slide switch allows attenuation of either x1 or x10 to be selected.
This probe is particularly useful if you want to probe CAN bus and FlexRay signals.
$24.75 each
____________________________________________________________________________________________________
Large Dolphin/Gator Clips
The crocodile clips are fully insulated with a 4 mm socket in the handle, offering an easy connection to the TA000 test lead. The toothed grip offers good contact on fine wire, with a 30 mm jaw opening limit.
$8.25 each
Black
Red
____________________________________________________________________________________________________
Sprung Hook Clips
These probes feature a shrouded 4 mm socket and allow you to hook your test lead on to small components. The hook can hold conductors up to 10 mm in diameter
$6.60 each
Black
Red
___________________________________________________________________________________________________
4mm Shrouded to Unshrouded Adapter
Shrouded-to-unshrouded adapters are for use with plugging the TA000 test leads into older style break out boxes that are not designed for use with shrouded 4 mm connectors.
$1.65 each
Black
Red
___________________________________________________________________________________________________
Multimeter Probes
The multimeter probes offer a quick and easy solution, where a permanent connection is not required. The 4 mm socket in the handle of the probe connects straight into the TA000 test lead.
$6.60 each
Black
Red
____________________________________________________________________________________________________
Secondary Ignition Pickup
Due to the high voltages involved in secondary ignition systems, it is not possible to make measurements by direct connection; attempting to make a direct connection will almost certainly damage the measuring instrument.
The PP178 is a capacitive pickup that simply connects around the insulation of an ignition circuit component such as a plug wire — this avoids the need for direct connection.
The PP178 comes with a shielded 2.5m (100 inch) lead. It is suitable for use with conventional ignition systems and most HEI and DIS systems.
$57.75 each
____________________________________________________________________________________________________
BNC socket to BNC socket cable with earth clamp
3 metre (9 ft 10 in) BNC socket to BNC socket cable with earth clamp for use with the Coil-On-Plug Ignition Probe (PP338).
$24.75 each
____________________________________________________________________________________________________
Small Crocodile/Gator Clips
The crocodile clips are fully insulated with a 4 mm socket in the handle, offering an easy connection to the TA000 test lead. The toothed grip offers good contact on fine wire, with a 11 mm jaw opening limit.
Black or red
$4.95 each
Black
Red
____________________________________________________________________________________________________
20:1 Attenuator
The PP198 has been designed to allow fuel injector and primary ignition waveforms to be measured using PicoScope oscilloscope products.
The PP198 is a passive 20:1 attenuator. This means that a 20V signal at its input will appear as a 1V signal on the output. As the signal is attenuated, the PP198 allows voltages of up to 300 V to be measured.
Please note this attenuator should not be used for any high voltage measurements other than fuel injectors and primary ignition.
$80.85 each
____________________________________________________________________________________________________
Automotive Test Leads (Standard Black Leads)
The TA000 test lead has been custom made for automotive use with a Pico automotive oscilloscope. Its length (3 meters / approx 10 ft) allows the oscilloscope to be placed on the work bench away from the car being tested / repaired. A wide range of probes, clips and gators can be plugged into the 4 mm connectors at the end of the cable. The cable is fully screened to reduce noise pickup.
$33.00 each
Also available is the TA020 automotive test lead. The TA020 is a 5 meter (approx 16 ft) version of the TA000.
$49.50 each
____________________________________________________________________________________________________
Acupuncture Probe Set
The TA008 is field repairable
And finally, here's the best part. Don't you just hate it when you are using a back pinning probe and it bends or breaks? Before the TA008 came along, this meant that you had to buy a whole new back-probe. Not with the TA008; it's repairable. If the pin becomes damaged or useless in any way, simply take your pocket screwdriver, remove the set screw, pull out the old pin and install the new one! There's no need to replace the whole probe.
$47.85 set
____________________________________________________________________________________________________
Empty Standard Case
$82.50 each
____________________________________________________________________________________________________
Pro Carry Case
The Pro Carry Case, as supplied with our top-of-the-range PicoQuad 4000 Deluxe Kit, is a high-quality case designed specifically to store and protect your PicoScope oscilloscope and accessories.
The hard outer shell of the case protects your kit from the inevitable knocks and bumps of workshop life, while the shock-absorbing foam inner lining holds your PicoScope and accessories secure. The case also features a divided compartment in the lid to keep all your probes, cables and manuals safe.
External dimensions:approximately 48 x 38 x 18 cm (18.9 x 14.9 x 7.1 in)
$163.35 each
____________________________________________________________________________________________________
BNC to 4 mm Adapter
The BNC to 4 mm adapter connects two 4 mm (“banana”) plugs to a BNC socket. If you have a sensor such as a current clamp with 4 mm plug outputs, for example, this adapter allows you to plug it into a PicoScope Automotive Oscilloscope with a BNC input. The 4 mm sockets and BNC plug are fully shrouded for safety.
$16.50 each
____________________________________________________________________________________________________
2-Pin Automotive Breakout Lead
The TA012 break out lead enables voltage readings to be taken from the numerous sensors in the engine compartment. The break out lead is simply connected into the existing cable loom, the output signal can then be taken from the two 4 mm banana plugs into the automotive oscilloscope using the TA000 test lead.
Note: a standard PicoScope test lead will be required to convert the 4 mm banana plug connection on the TA012 into a BNC connector suitable for plugging into the PicoScope.
$41.25 each
____________________________________________________________________________________________________
Piercing Clips
The TA007 Insulation Piercing Test Clip set is ideally suited for automotive test and diagnosis. The piercing clips allow the user to provide the exact pressure needed to pierce the insulation of a wide range of wire types and sizes. The clips also feature a rotating banana jack that prevents the test lead from twisting and keeps the oscilloscope in the circuit while the wire is pierced, providing immediate confirmation that contact with the conductor has been made.
$41.25 set of two, one black one red
____________________________________________________________________________________________________
Inductive Pickup
Produces a nice clean spike during an ignition event, great for using as a sync.
$74.25 each
TFI IV Pickup Tester Diode
This is the diode required to build the TFI IV Pickup Tester as found in the Creative Labscope Technique page Technical Articles
No other diode has been shown to be suitable. Obviously, since we have the only ones left on the planet, we are not giving them away. When they are gone, this tool will no longer be possible.
$20.00 Each
Free Shipping
Active Differential Oscilloscope Probe 
| Model | TA057 |
|---|---|
| Bandwidth | 25 MHz |
| Common mode | ±1400 V |
| Differential | ±140 V, ±1400 V |
| Battery power | Internal |
| Attenuation | 20:1, 200:1 |
| Input impedance | 4 MΩ / 5.5 pF |
| Safety rating | CAT III |
A must have for Hybrid Techs!
Allows measurement of high voltage levels along with ground isolation.
Cat III rated, Safely measure up to 1000 Volts with your lab scope.
$363.00 each
_____________________________________________________________________________________________________________________________
BNC To BNC Cable
1.8 meter
$8.25 each
_____________________________________________________________________________________________________________________________
BNC-Banana Adapter
These adapters allow the use of BNC accessories with Scopes and meters using Banana style connectors. These use the stackable style banana plugs. Both the adapter cable and the female/female adapter are included.
$20.00 each
