NEW!!
Set of 4 Colored Premium Test Leads: BNC Plug to 4 mm
The ground lead is detachable on all except the Blue channel A lead.
Available in standard 3 meter and extended 5 meter lengths.
Set of Four - 3 Meter $165.00 + $25.00 S&H UPS 3 Day
Set of four - 5 Meter $190.00 + $25.00 S&H UPS 3 Day
Individual 3 meter leads
Blue $49.50
Red $49.50
Green $49.50
Yellow $49.50
_________________________________________________________________________________________________
New!!
3 Meter Colored Lead Extension set
These will extend both the colored and standard black test leads.
Great for test drives.
$90.00 + $25.00 S&H UPS 3 Day
_________________________________________________________________________________________________
60 MHz Oscilloscope Probe (MI007)
This high-quality general purpose oscilloscope probe has a 60 MHz bandwidth. A two position slide switch allows attenuation of either x1 or x10 to be selected.
This probe is particularly useful if you want to probe CAN bus and FlexRay signals.
$24.75 each
____________________________________________________________________________________________________
USB Cables
These new cables are manufactured to Pico's specifications to help PicoScope users with poor quality or sloppy PC USB ports. These cables will likely help those who are experiencing occasional scope to PC communication disruptions.
Available in 1.8m (approx. 6 ft) and 4.5m (approx. 14.5 ft)
1.8m $8.25
4.5m $16.50
_________________________________________________________________________________________________
S-Hook
This small but essential accessory makes it easy to keep all those test leads tidy in the engine bay.
The S-hook is about 100 mm (4 in) long and coated in plastic and rubber to protect the vehicle's paintwork and your cables. Hook one end underneath the bonnet or hood, and use the other end to hang a bundle of cables up to about 25 mm (1 in) thick.
$3.30 each
____________________________________________________________________________________________________
4mm Shrouded to Unshrouded Adapter
Shrouded-to-unshrouded adapters are for use with plugging the TA000 test leads into older style break out boxes that are not designed for use with shrouded 4 mm connectors.
$1.65 each
Black
Red
___________________________________________________________________________________________________
BNC socket to BNC socket cable with earth clamp
3 metre (9 ft 10 in) BNC socket to BNC socket cable with earth clamp for use with the Coil-On-Plug Ignition Probe (PP338).
$24.75 each
____________________________________________________________________________________________________
20:1 Attenuator
The PP198 has been designed to allow fuel injector and primary ignition waveforms to be measured using PicoScope oscilloscope products.
The PP198 is a passive 20:1 attenuator. This means that a 20V signal at its input will appear as a 1V signal on the output. As the signal is attenuated, the PP198 allows voltages of up to 300 V to be measured.
Please note this attenuator should not be used for any high voltage measurements other than fuel injectors and primary ignition.
$80.85 each
____________________________________________________________________________________________________
Automotive Test Leads (Standard Black Leads)
The TA000 test lead has been custom made for automotive use with a Pico automotive oscilloscope. Its length (3 meters / approx 10 ft) allows the oscilloscope to be placed on the work bench away from the car being tested / repaired. A wide range of probes, clips and gators can be plugged into the 4 mm connectors at the end of the cable. The cable is fully screened to reduce noise pickup.
$33.00 each
Also available is the TA020 automotive test lead. The TA020 is a 5 meter (approx 16 ft) version of the TA000.
$49.50 each
___________________________________________________________________________________________________
BNC to 4 mm Adapter
The BNC to 4 mm adapter connects two 4 mm (“banana”) plugs to a BNC socket. If you have a sensor such as a current clamp with 4 mm plug outputs, for example, this adapter allows you to plug it into a PicoScope Automotive Oscilloscope with a BNC input. The 4 mm sockets and BNC plug are fully shrouded for safety.
$16.50 each
____________________________________________________________________________________________________
2-Pin Automotive Breakout Lead
The TA012 break out lead enables voltage readings to be taken from the numerous sensors in the engine compartment. The break out lead is simply connected into the existing cable loom, the output signal can then be taken from the two 4 mm banana plugs into the automotive oscilloscope using the TA000 test lead.
Note: a standard PicoScope test lead will be required to convert the 4 mm banana plug connection on the TA012 into a BNC connector suitable for plugging into the PicoScope.
$41.25 each
___________________________________________________________________________________________________
BNC To BNC Cable
1.8 meter
$8.25 each
_____________________________________________________________________________________________________________________________
BNC-Banana Adapter
These adapters allow the use of BNC accessories with Scopes and meters using Banana style connectors. These use the stackable style banana plugs. Both the adapter cable and the female/female adapter are included.
$20.00 each
